Benefits
- Extremely safe – avoidance of incorrect loading through optimum alignment of the bolt-on swivel in the load direction – even when subjected to tensile load
- Comfortable use through optimum support surface, readable angle of inclination and squeezing marks on the load ring (no kinking of the load ring)
- Additionally tested safety: DGUV-certified with H-stamp
Technical data
Rotation
360° (under load)Type of attachment
multi-legQuality grade
10Certification
H-stampOperating temperature
Load angle
± 90°Identification mark
Batch numberAttachment
Screw-inStandard
EN 1677-1Range of application Attachment devices
Attachment technologySafety factor
4Tilting
180°Dimensions
Options
Option thread
Option Identification mark
Options on request
Safety instructions
![](/out/media/BELASTUNGSWINKEL-DREHBAR_SHI-4_44X44_4C.jpg)
Please note the admissible load angle.
Handling
1.If the bolt-on swivel is to remain permanently on the load or used for rotating loads and turning them over, then it will be necessary to tighten it to a higher torque according to the product table.
2.For a once-only transport procedure, tighten hand-tight using a suitable tool (e.g. open-ended spanner according to DIN 895 or DIN 894) until lying flat against the contact surface. If the bolt-on swivel is to remain permanently on the load or used for ro
CAD
Planning
-
Benefits
Benefits
- Extremely safe – avoidance of incorrect loading through optimum alignment of the bolt-on swivel in the load direction – even when subjected to tensile load
- Comfortable use through optimum support surface, readable angle of inclination and squeezing marks on the load ring (no kinking of the load ring)
- Additionally tested safety: DGUV-certified with H-stamp
-
Technical data
Technical data
Rotation
- 360° (under load)
Type of attachment
- multi-leg
Quality grade
- 10
Certification
- H-stamp
Operating temperature
- –40 °C to +200 °C
- reduced carrying capacities outside this range
Load angle
- ± 90°
Identification mark
- Batch number
Attachment
- Screw-in
Standard
- EN 1677-1
Range of application Attachment devices
- Attachment technology
Safety factor
- 4
Tilting
- 180°
-
Dimensions
Dimensions
-
Options
Options
Option thread
- with UNC thread and other thread types
- with internal thread up to 15 t
- Variable thread lengths
Option Identification mark
- with RFID chip
- with individual serial number or labelling
- A selection of the options available on request can be found below. Please contact us for your individual offer!
Options on request
- in special designs
- in weldable design up to 32.5 t
-
Safety instructions
Safety instructions
Please note the admissible load angle.
-
Handling
Handling
1.If the bolt-on swivel is to remain permanently on the load or used for rotating loads and turning them over, then it will be necessary to tighten it to a higher torque according to the product table.
2.For a once-only transport procedure, tighten hand-tight using a suitable tool (e.g. open-ended spanner according to DIN 895 or DIN 894) until lying flat against the contact surface. If the bolt-on swivel is to remain permanently on the load or used for ro
-
CAD
CAD
Planning
Benefits
- Extremely safe – avoidance of incorrect loading through optimum alignment of the bolt-on swivel in the load direction – even when subjected to tensile load
- Comfortable use through optimum support surface, readable angle of inclination and squeezing marks on the load ring (no kinking of the load ring)
- Additionally tested safety: DGUV-certified with H-stamp
Technical data
Rotation
360° (under load)Type of attachment
multi-legQuality grade
10Certification
H-stampOperating temperature
Load angle
± 90°Identification mark
Batch numberAttachment
Screw-inStandard
EN 1677-1Range of application Attachment devices
Attachment technologySafety factor
4Tilting
180°Dimensions
Options
Option thread
Option Identification mark
Options on request
Safety instructions
![](/out/media/BELASTUNGSWINKEL-DREHBAR_SHI-4_44X44_4C.jpg)
Please note the admissible load angle.
Handling
1.If the bolt-on swivel is to remain permanently on the load or used for rotating loads and turning them over, then it will be necessary to tighten it to a higher torque according to the product table.
2.For a once-only transport procedure, tighten hand-tight using a suitable tool (e.g. open-ended spanner according to DIN 895 or DIN 894) until lying flat against the contact surface. If the bolt-on swivel is to remain permanently on the load or used for ro
CAD
Planning
-
Benefits
Benefits
- Extremely safe – avoidance of incorrect loading through optimum alignment of the bolt-on swivel in the load direction – even when subjected to tensile load
- Comfortable use through optimum support surface, readable angle of inclination and squeezing marks on the load ring (no kinking of the load ring)
- Additionally tested safety: DGUV-certified with H-stamp
-
Technical data
Technical data
Rotation
- 360° (under load)
Type of attachment
- multi-leg
Quality grade
- 10
Certification
- H-stamp
Operating temperature
- –40 °C to +200 °C
- reduced carrying capacities outside this range
Load angle
- ± 90°
Identification mark
- Batch number
Attachment
- Screw-in
Standard
- EN 1677-1
Range of application Attachment devices
- Attachment technology
Safety factor
- 4
Tilting
- 180°
-
Dimensions
Dimensions
-
Options
Options
Option thread
- with UNC thread and other thread types
- with internal thread up to 15 t
- Variable thread lengths
Option Identification mark
- with RFID chip
- with individual serial number or labelling
- A selection of the options available on request can be found below. Please contact us for your individual offer!
Options on request
- in special designs
- in weldable design up to 32.5 t
-
Safety instructions
Safety instructions
Please note the admissible load angle.
-
Handling
Handling
1.If the bolt-on swivel is to remain permanently on the load or used for rotating loads and turning them over, then it will be necessary to tighten it to a higher torque according to the product table.
2.For a once-only transport procedure, tighten hand-tight using a suitable tool (e.g. open-ended spanner according to DIN 895 or DIN 894) until lying flat against the contact surface. If the bolt-on swivel is to remain permanently on the load or used for ro
-
CAD
CAD
Planning